Plumbing Basics: Your Starting Point for When Installing a Bathtub
Plumbing Basics: Your Starting Point for When Installing a Bathtub
Blog Article
We have discovered the article relating to Tools You Need to Install a New Bathtub directly below on the web and concluded it made sense to write about it with you here.
Mounting a bathtub isn't exactly brain surgery, yet it does need strong plumbing, woodworking, and also in some cases, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately difficult task. If the old bathtub is conveniently available, the task can move quickly; if you need to open up a wall surface to remove the old bathtub as well as place the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to move out the old tub and also set in the new one. Make certain you have actually certified on your own for the work and are comfortable trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is better to take into consideration employing one prior to you begin. Opportunities are you may require a specialist plumber to make tube connections.
This post will certainly aid you mount a brand-new tub in your shower room if you have already purchased a new tub and do not require to alter the plan of your previous water supply pipelines.
Your tools and material checklist ought to make up the following:
Getting ready for the Installment
First of all, the sustaining frame provided with the bath must be fitted (if called for) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to prevent pressure on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its last placement.
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, then the first thing you must do is detach the water system. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome due to the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will originate from the pipes. When the supply pipelines have actually been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from turning during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to going on to fit the new taps, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Utilizing the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The next objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also readjusting the feet on the bath tub up until the level reads degree.
To mount taps, fit all-time low of the outermost flexible faucet adapter to the suitable supply pipe by making a compression sign up with; after that do the very same for the other tap.
Switch on the water system and also check all joints as well as new pipework for leakages and also tighten them if essential. Fill the bathtub and additionally examine the overflow outlet as well as the typical outlet for leaks.
Lastly, repair the bath paneling as explained in the maker's user's manual. Tiling and securing around the tub needs to wait until the tub has been used at least once as this will resolve it right into its final position.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washers remain in area between the tap as well as the sink. Safeguard the faucet in place with the producer supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former type should be connected to the faucet finishes first, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath meets the tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to break a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in complications with wetness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and installations. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to enable the activity experienced when the bathtub remains in usage. The sealant can split relatively early if you do not take into consideration this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that write-up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from an acquaintance on our other web blog. Be sure to set aside a second to share this write-up if you enjoyed reading it. Thank you so much for your time invested reading it.
Show Details Report this page